Mapei 114 UltraColor Plus Anthracite Grout 2kg

Product Information

When removing already cured Kerapoxy from the joints, use a hot air industrial drier. Remove hardened Mapei Kerapoxy from the tiles with Mapei Pulicol 2000. If the cleaning operation is carried out too soon (the mix is still too wet), some of the mix may be removed from the joints. If grouting is carried out in extremely hot, dry or windy weather, we Mapei Ultracolor Plus is suitable for grouting walls and floors in areas that are subject to intense traffic, such as shopping centres, airports, restaurants and other public spaces. It is also suitable for residential use in all areas, such as facades, balconies, terraces and swimming pools. Mapei Ultracolor Plus forms a smooth, compact finished surface with optimum resistance to abrasion, compression and flexural strength, and good resistance to acids with a pH > 3. Floors are ready for light foot traffic after approx. 3 hours. Surfaces grouted with Mapei Ultracolor Plus may be put into service after 24 hours. Basins and swimming pools may be filled up 48 hours after grouting. From our carrier you will receive a text message on the day of the delivery with a 2 hour delivery window. If there any changes or delays you will receive an update via text.

Mapei Kerapoxy Epoxy Tile Grout does not ensure perfect adhesion when used for grouting tiles with wet edges or contaminated with cement, dust, oil, grease, etc. After grouting with Mapei Kerapoxy, floors and walls should be cleaned immediately, before the product dries. Wet the surface thoroughly and emulsify with an abrasive pad for cleaning joints (such as Scotch-Brite or Kerakoll Cleaning Pads), making sure not to wash-out the joints. When cleaning walls, the cleaning pad should be fully soaked with water. The excess liquid can be removed with a hard cellulose sponge (e.g. Kerakoll Cellulose Sponge Float), and should be replaced when too full of resin. Use the same type of sponge for the final tooling of the grout. It is very important that once the finishing process has ended, no traces of Mapei Kerapoxy are left on the tile surface because it will be very difficult to remove. It is therefore necessary to frequently rinse the sponge with clean water during the cleaning process.When finishing large floor surface areas, use a rotary, disc-type power float with Scotch-Brite® abrasive pads, well saturated with water. All excess liquid can be removed with a rubber squeegee. The final cleaning cycle may be carried out using Mapei Ultracare Kerapoxy Cleaner for epoxy grout (special cleaning solution for epoxy grout). Mapei Kerapoxy Cleaner may also be used to remove thin residues of grout several hours after application. In such cases, the product must be left to react for longer (15-20 mins.). The efficiency of Mapei Kerapoxy Cleaner depends on the amount of resin residues and how much time has passed since application. Cleaning must always be carried out while “fresh” as described above. Mapei Ultracolor Plus is available in 2kg and 5kg bags, in the following colours: Please note, only some colours are available in 2kg bags.

You must be available to accept delivery on the date you have requested, failure to do so will result in paying for a re delivery charge.

Spread Mapei Kerapoxy with an appropriate grout float, making sure the joints are completely filled. Use the same float, but on edge, to remove excess grout. Final cleaning of the powdery film of Mapei Ultracolor Plus from the surface may be carried out with a clean, dry cloth. Mapei Ultracolor Plus creates water repellent grout joints that have excellent colour uniformity. All colours are resistant to UV rays and atmospheric agents. Mapei Ultracolor Plus does not contain Portland cement and must not be mixed with gypsum or other hydraulic binders; never add water to the mix once it has started to set. Unglazed klinker tiles should be grouted with the same colour tone Kerapoxy. All other colours should be used only with glazed tiles.After the final cleaning operation, if the surface still has traces of Mapei Ultracolor Plus due to incorrect application, it may be cleaned down with an acidic cleaner (e.g. Keranet), by following the relevant instructions, at least 24 hours after grouting the joints. Only use Keranet on surfaces which are resistant to acid, and never use it on marble or limestone material. All Mapei Ultracolor Plus grout colours are also available in a matching silicone – Mapesil AC Silicone. If using this grout with moisture sensitive natural stone tiles, a low modulus silicone is advised – Mapei Mapesil LM Silicone. Acid-resistant bonding of tiles (used as an adhesive in compliance with class R2T specification according to EN 12004 standard). Applying the grout: Fill the joints with the Mapei Ultracolor Plus mix using a special MAPEI grout float or rubber squeegee, without leaving any gaps or steps. Remove any excess of Mapei Ultracolor Plus from the surface, by moving the float diagonally to the joints while the mix is still fresh. Mapei Kerapoxy Epoxy Tile Grout allows you to create floors, walls and worktops, etc. in compliance with the HACCP system and the requirements of EC Regulation No. 852/2004 regarding hygiene and foodstuffs.